RabbitLink EG2110 Instrukcja Użytkownika

RabbitLink (EG2100)Network Programming GatewayUser’s Manual019–0090 • 020222–B

6 RabbitLink (EG2100)2. Connect the programming cable to configure network parameters from your PC.Connect the 10-pinDIAG connector of the programming

User’s Manual 73. Connect the power supply.Two options are available for powering the RabbitLink—via an AC adapter to power supply jackJ4, or througha

8 RabbitLink (EG2100)2.2 Configuring RabbitLink Network Parameters from Your PCThere are two ways to set the basic network parameters for the RabbitLi

User’s Manual 9The RabbitLink boots up whenever the power cycles, and then displays the message,RabbitLink Serial Console Version X.XXThe RabbitLink s

10 RabbitLink (EG2100)2.4 Ethernet ConnectionsBefore proceeding, you will need to have either two straight-through Ethernet cables and an Ether-net hu

User’s Manual 113. RABBITLINK SOFTWAREThis chapter describes the software functionality available when using a RabbitLink.3.1 Downloading and Debuggin

12 RabbitLink (EG2100)3.1.3 Password Protect the Embedded TargetThough not required, it is highly recommended that the passphrase security feature be

User’s Manual 133.2 RabbitLink FirmwareThe firmware necessary to operate the RabbitLink with a Rabbit-based target system is loaded atthe factory. Thi

14 RabbitLink (EG2100)3.2.2 Firmware UpgradesFollow the above steps to install a firmware upgrade. Just substitute the name of the firmwareupgrade for

User’s Manual 15APPENDIX A. SPECIFICATIONSAppendix A provides the specifications for the RabbitLink and describes the conformalcoating.

ii RabbitLink (EG2100)RabbitLink (EG2100) User’s ManualPart Number 019-0090 • 020222–B • Printed in U.S.A.©2001 Z-World Inc. • All rights reserved.Z-W

16 RabbitLink (EG2100)A.1 Electrical and Mechanical SpecificationsFigure A-1 shows the mechanical dimensions for the RabbitLink.Figure A-1. RabbitLink

User’s Manual 17Table A-1 lists the electrical, mechanical, and environmental specifications for the Rab-bitLink.Table A-1. RabbitLink SpecificationsP

18 RabbitLink (EG2100)A.2 Conformal CoatingThe areas around the crystal oscillator and the battery backup circuit on the RabbitLinkhave had the Dow Co

User’s Manual 19APPENDIX B. PLASTIC ENCLOSUREThe plastic enclosure provides a secure way to enclose your RabbitLink board. The enclosureitself may be

20 RabbitLink (EG2100)B.1 Assembly1. Attach the RabbitLink board to the plastic enclosure base.Position the RabbitLink board over the plastic enclosur

User’s Manual 21cyanoacrylate or contact cement to the inside of the enclosure around each light pipe to hold it inplace.NOTE: Once the glue is applie

22 RabbitLink (EG2100)B.2 DimensionsFigure B-4 shows the dimensions for the plastic enclosure.Figure B-4. Plastic Enclosure DimensionsWhen fully assem

User’s Manual 23APPENDIX C. SUBSYSTEMSAppendix D describes the principal subsystems for the RabbitLink.• RabbitLink Subsystems• Serial Communication•

24 RabbitLink (EG2100)C.1 RabbitLink Hardware SubsystemsFigure D-1 shows the Rabbit-based subsystems designed into the RabbitLink and shows the paral-

User’s Manual 25C.2 Serial CommunicationC.2.1 Serial Programming PortsThe RabbitLink board has two 10-pin programming headers labeled J8 and J9. ThePR

User’s Manual iiiTABLE OF CONTENTSChapter 1. Introduction 11.1 RabbitLink Features...

26 RabbitLink (EG2100)C.3 MemoryC.3.1 SRAMThe RabbitLink is designed to accept 128K or 512K of SRAM packaged in an SOIC case.The standard models sold

User’s Manual 27C.4 Power SuppliesPower is supplied to the RabbitLink board from an external source either through jack J4 orthrough screw terminal co

28 RabbitLink (EG2100)

User’s Manual 29APPENDIX D. PROGRAMMING CABLEAppendix E provides additional information for the Rabbit 2000™microprocessor when using theDIAG and PROG

30 RabbitLink (EG2100)The programming port, which is shown in Figure E-1, can serve as a convenient communicationsport for field setup or other occasi

User’s Manual 31APPENDIX E. SERIAL CONSOLECOMMANDSThis appendix describes the RabbitLink serial console commands. The serial console wasdesigned to be

32 RabbitLink (EG2100)E.1 Configuration CommandsThese commands are used to set network parameters and to password protect the RabbitLink.set gateway &

User’s Manual 33E.2 Variables CommandsThe RabbitLink serial console has the ability to handle SSI (Server Side Includes) variables. Thesevariables are

34 RabbitLink (EG2100)E.3 File Commandsgetv <varname>This command gets the value of the specified variable. The value is printed using the forma

User’s Manual 35list filesThis command lists all the files in the flash file system on the RabbitLink.put <filename><body of file><ctrl

iv RabbitLink (EG2100)C.1 RabbitLink Hardware Subsystems ...

36 RabbitLink (EG2100)E.4 E-Mail Commandsmail <e-mail address><subject><body><ctrl-D>The mail command sends an e-mail via the

User’s Manual 37E.5 Other Console Commandsecho <on | off>This command toggles the echoing of characters.help [filename]This command displays the

38 RabbitLink (EG2100)E.6 RabbitLink Console API (prior to Dynamic C 7.20)The RabbitLink serial console may be accessed via the serial port using the

User’s Manual 39int ConsoleFinish(long timeout);This function finishes receiving data from the RabbitLink serial console by blocking foran optional am

40 RabbitLink (EG2100)

User’s Manual 41INDEXAAC adapter ... 7Cconfiguration ...8echo on ... 8

42 RabbitLink (EG2100)

User’s Manual 43SCHEMATICS090-0112 RabbitLink (EG2100) Schematicwww.rabbitsemiconductor.com/documentation/schemat/090-0112.pdf090-0085 Programming Cab

User’s Manual 11. INTRODUCTIONThis chapter introduces the RabbitLink Network Programming Gateway and describes its features.Rabbit-based embedded syst

2 RabbitLink (EG2100)1.2 Development and Evaluation ToolsThe RabbitLink board comes with a program download cable. This cable connects a Rabbit-basedc

User’s Manual 31.2.1 Manual ConventionsA black square indicates pin 1 of all headers.1.3 SoftwareThe RabbitLink board is shipped with firmware already

4 RabbitLink (EG2100)

User’s Manual 52. GETTING STARTEDThis chapter shows how to make the necessary hardware connections and how to configure thenetwork parameters for the